Linde Electric Forklift Truck 336-03 series: E25, E30, E25/600, E30/600 Operating Manual (User Manual)

Linde Electric Forklift Truck 336-03 series: E25, E30, E25/600, E30/600 Operating Manual (User Manual)

Original Illustrated Factory Operating Manual For Linde Electric Forklift Truck 336-03 series

Covered models:

Format: PDF, 104 pages
Language: English

Table of content:
Approved applications
Impermissible use
Description of use and climatic conditions
Technical note
Truck takeover
EC declaration of conformity

Type plate
Technical data
Noise emission value
Frequency characteristic for human body vibratio
Technical description
Hydraulic system
Electrical system
General view of truck
Controls and indicators
Composite instrument
Hour meter
Battery discharge indicator

Beginning operation
Safety rules
Safety information
Handling fluids and lubricants
Periodic safety inspection
Residual risks
Operation of industrial trucks in the plant area
Running-in instructions
Checks and services prior
to initial operation of the truck
Daily checks
Daily checks and servicing before operation
Check the tyre inflation pressure
Check the tightness of the wheel nuts
Opening the overhead guard
First lock-in position: Servicing position
Second lock-in position: Battery change
Closing the overhead guard
Check the battery charge
Charging the battery
Connecting the battery to a suitable external charger ….
Check the condition, electrolyte level and
specific gravity of the battery
Battery change
Battery removal with a crane
Adjusting the driver’s seat
Adjusting the swivel seat
Adjusting armrest of the driver’s seat
Applying the seat belt
Opening the seat belt
Push the emergency stop button
Pull the emergency stop button
Entering and exiting the truck

Travel in the forward direction
Travel in the reverse direction
Reversing the direction of travel
Malfunctions during operation
Single-pedal model
Steering system
Braking system
Service brake, regenerative brake
Foot brake
Operating the electric motor brake (LBC)
Engaging the handbrake
Releasing the handbrake
Central control lever (joystick) operation of mast and
Tilting the mast forward
Tilting the mast back
Raising the fork carriage
Lowering the fork carriage
Operating the attachments
Operating the sideshift
Operating the clamp
Single control lever operation of mast and attachments
Additional capacity rating plate for attachments
Additional capacity rating plate for attachments with
loads that are not clamped
Additional capacity rating plate for attachments with
loads that are fixed or clamped
Turning on the front working lights
Turning on the rear working lights
Turning on the front windscreen wiper and washer
Turning on the rear windscreen wiper
Turning on the lighting
Turning on the hazard warning light
Turning on the directional indicator lights
Electric heater
Heater controls
Truck Data Management (LFM)
Truck data acquisition
Condition code
Truck data acquisition – default setting
(PIN number and condition code)
Truck data acquisition – special setting
(PIN number)
Forklift Data Acquisition via RFID chip or
magnetic strip card
Operating the horn
Opening the electrical compartment cover
Closing the electrical compartment cover
Checking, renewing the fuses
Automotive fuses
Main circuit fuses
Fuses (options)
Before loading
Positioning the forks
Transporting the load
Before leaving the truck
Tow coupling
Forced opening of overhead guard without
Bowden cable
Transporting the truck on a lorry or low-bed trailer
Hoisting the truck
Hoisting the truck with a crane
Hoisting the truck with the eyebolts
Wheel change
Jack locations
Changing the rear wheels
Changing the front wheels
Mast removal
Towing instructions
Towing procedure
Tilting the mast manually
Lowering the forks manually
Emergency exit for trucks with rear windscreen
Emergency exit for trucks with polycarbonate rear wind¬screen

Taking the truck out of operation
Measures before taking the truck out of operation
Putting the truck back into operation
Disposal of old vehicles
General information
Maintenance intervals
Work on the mast and on the front part of the truck
Securing the mast against tilting back
Standard mast
Securing the raised standard mast
Duplex mast
Securing the raised duplex mast
Triplex mast
Securing the raised triplex mast
Services after the first 50 hours of operation
Inspection and maintenance chart

Inspection and maintenance as required
Check seat belt for condition and operation
Clean the lift truck
Clean and spray the lift chain
Tighten the wheel nuts
Check the tyres for damage and foreign objects
Check the security of the hydraulic oil tank
Lubricate the steer axle, mast and tilt cylinder bearings .
Clean electrical heater
Other cleaning and greasing work
Inspection and maintenance every
500 to 1000 hours or annually
Clean the steering axle
Lubricate the steering axle
Inspect the joystick boot
Check the control unit for function
Clean the left and right wheel traction, power steering and working

hydraulics pump motors
Clean the tractor compartment, lift motor, lift and power
module fans
Clean the digital control
Lubricate the mast and tilt cylinder pivots
Retighten the mast fastening bolts
Sideshift: Clean, grease and check the mounting
Check the braking system
Check the brake linings, lubricate the brake lever pivot .
Check the working and steering hydraulics for leaks
Check the counterweight, electric motors, chassis,
wheel drives, overhead guard and steering axle for security
Mast, lift chain, lift cylinder and end stops:
Check condition, mounting and function
Adjust the lift chain length, Lubricate the lift chain with chain pray
Check the fork quick-releases and fork stops
Check the pre-tension of double hoses if attachments are fitted
Check the hydraulic oil level
Check and oil the pedal and travel control linkage
pivots and overhead guard lock
Grease the overhead guard pivots
Check and lubricate other pivots and joints
Check the contactor
Change the wheel drive oil
Check the electric cables, cable connectors and connections for

condition and tightness
Renew the breather filter
Renew the suction filter
Change the pressure filter
Check the wheel drives for oil leaks
Check the condition of the antistatic ribbon
Check heating operation
Inspection and maintenance every
3000 hours or every 2 years
Renew the hydraulic oil
Change the oil in wheel drive
Inspection and maintenance specifications
Lubricant recommendations
Hydraulic oil
Bio hydraulic oil
Gear oil
Lubricating grease
Battery grease
Chain spray
Troubleshooting guide
Electric circuit diagram (standard equipment)
Electric circuit diagram (options)
Auxiliary voltage transformer (125 W)
Auxiliary voltage transformer (250 W)
Auxiliary voltage transformer (400 W / 12 V)
Auxiliary voltage transformer (400 W / 24 VOUT)
Hydraulic circuit diagram

0 sales

0 sales

Download Category:
Download Tags: , , ,

Copyright 2016